« previous next »
Pages: 1 ... 7 8 [9] 10 11 12   Go Down

Author Topic: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..  (Read 34132 times)

0 Members and 1 Guest are viewing this topic.

Offline ClockmanFrance

  • Full Member
  • ***
  • Posts: 171
  • Karma: +11/-0
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #120 on: February 29, 2016, 12:37:39 pm »
There be Pulses on the yellow lead.

This will keep the PJ control board happy, it needs its pulsed fan.
Logged

Offline MarNet

  • Full Member
  • ***
  • Posts: 60
  • Karma: +0/-0
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #121 on: February 29, 2016, 01:22:27 pm »
Thank you clockman
2.2k resistor would be enough?
I don't have an oscilator but I'll post the picture when I'll finish with
Logged

Offline MarNet

  • Full Member
  • ***
  • Posts: 60
  • Karma: +0/-0
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #122 on: February 29, 2016, 05:41:27 pm »
One more thing, with a 4.7k resistor i have 8.2vcc power in tacho pin.
With 10k resistor i have 7.8vcc.
Clockman,  can you check what power do you have in the tacho pin with 2.2k resistor?
I'm waiting for the 2.2k resistor to be delivered
Thank you
Logged

Offline MarNet

  • Full Member
  • ***
  • Posts: 60
  • Karma: +0/-0
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #123 on: March 03, 2016, 06:17:57 am »
Hi all
With 2.2k resistor signal power output is 8.14v...
Logged

Offline frwainscott

  • Newbie
  • *
  • Posts: 21
  • Karma: +0/-0
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #124 on: March 06, 2016, 09:03:23 pm »
Hey Dudes, The 3 wire fans are old computer cooling fans or newer processor cooling fans.

I have attempted to attach a picture of both.

Frank
Logged

Offline MarNet

  • Full Member
  • ***
  • Posts: 60
  • Karma: +0/-0
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #125 on: March 13, 2016, 04:25:06 am »
And there is my inverter
I have to install it in a nice box now.
Logged

Offline oztules

  • Moderator
  • Hero Member
  • *****
  • Posts: 1177
  • Karma: +105/-8
  • Village idiot
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #126 on: March 13, 2016, 05:17:47 am »
Nicely done.
Have you had it under loads yet?

...........oztules
Logged
Flinders Island...... Australia

Offline MarNet

  • Full Member
  • ***
  • Posts: 60
  • Karma: +0/-0
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #127 on: March 13, 2016, 05:24:49 am »
Yes.
Just an 1.2kw angle grinder. 3kw start impulse, no change of noise or heat in 15 minutes use.
0.8A on idle
I'll install it on my farm in the next 2 weeks or so and I'll let you know guys.
Logged

Offline MarNet

  • Full Member
  • ***
  • Posts: 60
  • Karma: +0/-0
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #128 on: May 04, 2016, 12:49:41 pm »
Hello all
I tested my inverter with an mig welder.
The welding time power consumption was 2.6kw with a spoke of 5.6kw at start. No noise or anything else.
Thanks oztules,  thanks clockman.
I'm building an vertical axis wind turbine now,
I'm very busy :) Sorry for the late reply...
Logged

Offline oztules

  • Moderator
  • Hero Member
  • *****
  • Posts: 1177
  • Karma: +105/-8
  • Village idiot
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #129 on: May 04, 2016, 03:49:05 pm »
Good result.

.............oztules
Logged
Flinders Island...... Australia

Offline oztules

  • Moderator
  • Hero Member
  • *****
  • Posts: 1177
  • Karma: +105/-8
  • Village idiot
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #130 on: May 05, 2016, 07:14:14 pm »
Logged
Flinders Island...... Australia

Offline frackers

  • Full Member
  • ***
  • Posts: 239
  • Karma: +9/-0
  • If it moves - computerise it!
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #131 on: May 06, 2016, 05:01:39 am »
Quote from: oztules on May 05, 2016, 07:14:14 pm
Seems a real attempt to sell PJ parts now.
Really? Empty here!!
Logged
Robin Down Under (or are you Up Over!)

Offline MarNet

  • Full Member
  • ***
  • Posts: 60
  • Karma: +0/-0
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #132 on: May 06, 2016, 10:05:49 am »
Omg. Some prices there :(
Come on oztules, finish that EGS002 thing
I'm in as well if is any space for me :)
Logged

Offline oztules

  • Moderator
  • Hero Member
  • *****
  • Posts: 1177
  • Karma: +105/-8
  • Village idiot
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #133 on: May 06, 2016, 01:27:23 pm »
Marnet, the 002 has been superseded now, but the final working version of mine was here.... http://www.anotherpower.com/board/index.php/topic,1116.msg11540.html#msg11540

Works perfectly fine.

Antman has another version, and i'm sure more versions  will turn up sooner or later...

Tinker has done a schematic as well here:
http://www.thebackshed.com/forum/forum_posts.asp?TID=8542&get=last#93561

and a different style of output board etc here:
http://www.thebackshed.com/forum/forum_posts.asp?TID=8542&PN=0&TPN=3

Frackers, there was a complete list of all the boards there yesterday... today hardly any left.... amazing...

...............oztules
Logged
Flinders Island...... Australia

Offline MarNet

  • Full Member
  • ***
  • Posts: 60
  • Karma: +0/-0
Re: Building a 6kw pure sine wave inverter using power jack boards part2 the guts..
« Reply #134 on: May 06, 2016, 04:24:59 pm »
When you think that you start it :)
Do you feel a bit guilty?  Ahahahaha :)
If you ever around Ireland i would like to have pint with you.
I'll drop any inverter project now.
I have to finish a wind generator/turbine with lenz2 blades and i have to finish a python software for my farm.
Actually i have a system running on arduino and i transfer everything to beaglebone.  I hope I'll have everything done by 1st of august. I'll post everything i promise.
Logged
Pages: 1 ... 7 8 [9] 10 11 12   Go Up
« previous next »